Description
Number of Pages: 38
This is a reproduction, not a photocopy, of an original Nichols Twin Horizontal Milling Machine Instructions and Parts Manual. This manual contains all the information listed below in the contents.
Contents:
|
Introduction – The Nichols Twin Mill………………………………………. |
5 |
|
Description………………………………………………………………………… |
6 |
|
Machine Nomenclature………………………………………………………… |
7 |
|
Special Features of Construction……………………………………………. |
8 |
|
I The Spindle and its Drive……………………………………………………. |
9 |
|
II The Table Cycle……………………………………………………………… |
10 |
|
III Cutter Retraction……………………………………………………………. |
11 |
|
IV Double Cycle (Roughing & Finishing)…………………………………. |
12 |
|
V Brake Motors…………………………………………………………………. |
13 |
|
VI Coolant Equipment…………………………………………………………. |
14 |
|
Installation Procedure …………………………………………………………. |
15 |
|
General Set-Up Procedure…………………………………………………… |
16 |
|
Retraction Set-Up Procedure……………………………………………….. |
17 |
|
Double Cycle Set-Up Procedure…………………………………………… |
18 |
|
Maintenance………………………………………………………………………. |
19 |
|
Lubrication………………………………………………………………………… |
20 |
|
Trouble Shooting Hints………………………………………………………… |
21 |
|
To Change Spindle Bearings…………………………………………………. |
22 |
|
ILLUSTRATIONS |
23 |
|
Front View – Figure 1………………………………………………………….. |
24 |
|
Rear View – Figure 2 ………………………………………………………….. |
25 |
|
Head Gear Train-Plan View – Figure 3…………………………………… |
26 |
|
Air Motor and Control – Figure 4 …………………………………………. |
27 |
|
Hydro-Check – Figure 5………………………………………………………. |
28 |
|
Cutter Retraction – Figure 6………………………………………………….. |
29 |
|
Lubrication Chart – Figure 7…………………………………………………. |
30 |
|
Dimension Drawings – Figure 8……………………………………………… |
31 |
|
PLATE INDEX – Figure 9…………………………………………………… |
33 |
|
Plate 1. Spindle and Outboard Arbor Support…………………………. |
34 |
|
Plate 2. Primary and Intermediate Shafts…………………………………. |
36 |
|
Plate 3. Saddle and Coolant System………………………………………. |
38 |
|
Plate 4. Knee…………………………………………………………………….. |
40 |
|
Plate 5. Table-Rear…………………………………………………………….. |
42 |
|
Plate 6. Table-Front……………………………………………………………. |
44 |
|
Plate 7. Automatic Way Lubrication……………………………………….. |
46 |
|
Plate 8. Cutter Retraction…………………………………………………….. |
48 |
|
Plate 9. Transverse Pneumatic Feed-Third Slide Type……………….. |
50 |
Overview:
I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. I believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. My manuals are not photocopies. I maintain a high standard of quality in my reproductions. Most of the manuals I reproduce look better than their originals. I have professionally digitally edited every page, and removed stains, wrinkles and handwriting. All of the manuals are printed on thick white paper to withstand shop wear and tear.
