Description
Number of Pages: 32
This is a reproduction, not a photocopy, of an original Rivett 608 Lathe Bulletin (608D). The bulletin is a lot more than just a sales flyer; It should almost be considered a operator’s and set up manual. The bulletin shows some of the accessory set ups in use and descriptions of each accessory. There is even a gear chart included plus the contents listed below.
Contents:
Angle Iron…………………………………………………………………………. | 18 |
ArborsInternal Wheel………………………………………………………. | 10 |
Bench, Unit……………………………………………………………………….. | 23 |
Cabinet, oak……………………………………………………………………… | 25 |
Cabinet, steel…………………………………………………………………….. | 33 |
Carriage and Saddle……………………………………………………………. | 5 |
Centers…………………………………………………………………………….. | 20 |
Change Gears……………………………………………………………………. | 4 |
Chucks- |
20 |
Drill, Jaw and Step……………………………………………………………… | 21 |
Collets……………………………………………………………………………… | 21 |
Cutting Off and Forming Slide………………………………………………. | 17 |
Cutting Off and Turning Slide………………………………………………… | 17 |
Dog, Clamp………………………………………………………………………. | 18 |
Drawer, Wooden Bench Type………………………………………………. | 23 |
Drives- Diagrams……………………………………………………………….. | 30 |
Overhead C’shaf………………………………………………………………… | 27 |
Overhead C’shaft with aux. C’shaft att……………………………………. | 27 |
Horizontal Safety………………………………………………………………… | 22 |
Horizontal Safety with aux. C’shaft att…………………………………….. | 23 |
Motor Jackshaft…………………………………………………………………. | 33 |
Speed Box Motor………………………………………………………………. | 26 |
Speed Box Motor, Overhead att. Motor Drive………………………… | 26 |
Electrical Controllers…………………………………………………………… | 25 |
Gear Tables- English…………………………………………………………… | 28 |
Gear Tables- Metric……………………………………………………………. | 29 |
Grinder, Traverse……………………………………………………………….. | 15 |
Grinding Attachments:Belt Driven | |
Internal, Ecc. Slide Rest Type……………………………………………… | 10 |
External, Ecc. Slide Rest Type……………………………………………… | 10 |
Internal, Rocker Tool Post Type……………………………………………. | 10 |
External, Rocker Tool Post Type…………………………………………… | 10 |
Grinding Attachment:- |
|
Internal set-up……………………………………………………………………. | 9 |
External set-up…………………………………………………………………… | 9 |
Indexing Attachments:Change Gear Lathe……………………………. | 13 |
Gear Box Lathe…………………………………………………………………. | 13 |
Interlock, Carriage……………………………………………………………… | 5 |
Knurling Attachment……………………………………………………………. | 8 |
Lever Chuck Closer:- Change Gear Lathe………………………………. | 4 |
Gear Box Lathe…………………………………………………………………. | 4 |
Milling AttachmentsCarriage……………………………………………… | 12 |
Slide Rest…………………………………………………………………………. | 12 |
Thread……………………………………………………………………………… | 14 |
Traverse…………………………………………………………………………… | 14 |
Motors and Controllers……………………………………………………….. | 25 |
Oil Pan, on legs………………………………………………………………….. | 24 |
Oil Pump and Piping……………………………………………………………. | 24 |
PlatesDriving and Face…………………………………………………….. | 19 |
Quick Change Gear Box……………………………………………………… | 4 |
Relieving Attachment………………………………………………………….. | 15 |
Rests:Ball Turning……………………………………………………………. | 11 |
Comp. Slide, Eccentric………………………………………………………… | 6 |
Comp. Slide, Rocker………………………………………………………….. | 7 |
Follower…………………………………………………………………………… | 18 |
Steady……………………………………………………………………………… | 18 |
Tee………………………………………………………………………………….. | 18 |
Triangle…………………………………………………………………………….. | 18 |
Saw Table………………………………………………………………………… | 18 |
Slotting Attachment…………………………………………………………….. | 13 |
Slotting and Milling Fixtures………………………………………………….. | 18 |
Specifications…………………………………………………………………….. | 33 |
Spiral Attachment……………………………………………………………….. | 15 |
Tailstocks:Standard…………………………………………………………. | 8 |
Set Over…………………………………………………………………………… | 8 |
Taper Attachment………………………………………………………………. | 8 |
Thread Dial……………………………………………………………………….. | 9 |
Thread Tool………………………………………………………………………. | 5 |
Tools:Ecc. Slide Rest Type……………………………………………….. | 11 |
Rocker Tool Post Type……………………………………………………….. | 6 |
Treadles, Latch………………………………………………………………….. | 7 |
Turrets, Automatic Indexing………………………………………………….. | 23 |
Turret Attachment, Tailstock………………………………………………… | 16 |
Turret Tools………………………………………………………………………. | 16 |
Vises:Ecc. Slide Rest Type……………………………………………….. | 8 |
Rocker Tool Post Type……………………………………………………….. | 19 |
Overview:
I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. I believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. My manuals are not photocopies. I maintain a high standard of quality in my reproductions. Most of the manuals I reproduce look better than their originals. I have professionally digitally edited every page, and removed stains, wrinkles and handwriting. All of the manuals are printed on thick white paper to withstand shop wear and tear