Posted on

Machine ID’d: South Bend 13″ x 6′ Metal Lathe Catalog No.1866-C similar to 166-C

South 2BBend

We had one of our readers that wanted to learn more about his great 13″ x 6′ South Bend metal lathe. These South Bend lathes are beautiful machines They were built like tanks. As long as you install them properly, keep them clean, keep them trim, and oil the lathe properly they should last forever.

The serial number of his lathe was No. 50328 and the catalog number was stamped 1866-C as you can see in the picture below. This information dates his lathe around 1931. The reader wanted some clarification as to if the 1866-C was misstamped, because most of the information and advertisements with a similar machine show the catalog number as 166-C.

 

The 1866-C is a real and correct catalog number for your lathe. The difference between the 1866-C and the 166-C is the 1866-C was considered a “Tool Room Precision Lathe”, which came with various attachments like the collet attachment, taper attachment, threading dial, etc…

This particular South Bend lathe is part of the “N” series, which is distinguished mainly by the design of the apron. The “N” series wasn’t in production for very long. South Bend started producing them around 1930. It was replaced by the “R” series after 1934, and that is what South Bend used to the end. They sold the “N” until about 1937. There is always a lot of overlap with South Bend on some of their parts.

Here are some pictures of the South Bend Lathe after it has been cleaned some.

 

Manuals for South Bend 13″ x 6′ Metal Lathe Catalog No.1866-C

We have a few manuals that cover this South Bend 13″ x 6′ Metal Lathe Catalog No.1866-C. We have new revised parts manual that shows the main parts of the lathe here:

 

These are very helpful when trying to take the the lathes apart or put them back together. Also, locating parts can become easier, because most parts have the part number casted into them.
We also have a manual that shows explosive view parts break down diagrams of the accessories for these larger lathes like the, taper attachment, milling attachment, threading dial, turrets, collets, steady rest, etc… here:
A lot of people didn’t realize the the threading dial was an accessory. It seems like a common part today, but it is actually possible to do threading well without the dial and the version of How to Run A Lathe explains this procedure.
South Bend basically made one book for operations that covered all their lathes, but it is important to find the one that covers the correct vintage, because they made lots of changes to these lathes over the years. They keep the book with the same title “How to Run a Lathe” all through out the years, with different editions. The edition we have here covers this style of lathe, and we’ve enlarged it so it is easier to read:



 

Submit Your Machine
Do you want to know more about your machine?

Email us your details with pictures, and we’ll put together the best information we can find. Plus, we can get other readers’ input to help you learn more.

Also, feel free to email us if you want us to share your machine on our site.

Email your information to: info@ozarkwoodworker.com

Posted on

Machine ID’d: CL-195-C South Bend 16/24 Metal Lathe

IMG 20130925 04169

Received this image of a South Bend heavy metal lathe the other day. It was made in the 1950’s, and has a 6 foot bed catalog number CL-195-C. These South Bend lathes are beautiful machines They were built like tanks. As long as you install them properly, keep them clean, keep them trim, and oil the lathe properly they should last forever.

We have a few manuals that cover this lathe. We have a parts manuals with exploded view diagrams that shows the main parts of the lathe here:

These are very helpful when trying to take the the lathes apart or put them back together. Also, locating parts can become easier, but most parts have the part number casted into them. 
We also have a manual that shows explosive view parts break down diagrams of the accessories for these larger lathes like the turrets, collets, steady rest, etc… here:
A lot of people didn’t realize the the threading dial was an accessory. It seems like a common part today, but it is actually possible to do threading well without the dial and the version of How to Run A Lathe explains this procedure
South Bend basically made one book for operations that covered all their lathes, but it is important to find the one that covers the correct vintage, because they made lots of changes to these lathes over the years. They keep the book with the same title “How to Run a Lathe” all through out the years, with different editions. The edition we have here covers this style of lathe, and we’ve enlarged it so it is easier to read:

Submit Your Machine
Do you want to know more about your machine?

Email us your details with pictures, and we’ll put together the best information we can find. Plus, we can get other readers’ input to help you learn more.

Also, feel free to email us if you want us to share your machine on our site.

Email your information to: info@ozarkwoodworker.com

Posted on

Machine ID’d: 1931 South Bend 9″ Metal Lathe

Received these pictures of an old bench top South Bend 9″ metal lathe with a quick change gearbox and vertical drive system. It has serial number 50293 stamp on the tailstock end of the bed.

 

 

 

 

 

We have two different manuals that cover this machine and were able to assist this reader. Quality manuals for this older lathe can be difficult to find.

 

We have a parts manual here:

 

 

 

The parts manuals for all the South Bend lathes, besides the geared head lathes made in the 70’s, combine a large selection of lathes that they manufacturer at one time in one book. Since South Bend offered so many different options and combinations it was easier for them to combine them and let the operator decide what parts pertain to his model in the manual.

 

The operator’s manual for this vintage of lathe would be contained in the book we have here:

 

 

 

Like the parts manual, South Bend combined a lot of information in the book that covered a variety of styles and models they made at the time. It is important to find the correct version of How to Run a Lathe so it shows you how to set up the correct style of gearbox and other settings. This older version of How to Run a Lathe has been enlarged making it easier to read while still allowing everything to be crisp and clear. We are able to achieve this, because of the high resolution scans we do of all our manual reproductions.

Submit Your Machine
Do you want to know more about your machine?

Email us your details with pictures, and we’ll put together the best information we can find. Plus, we can get other readers’ input to help you learn more.

Also, feel free to email us if you want us to share your machine on our site.

Email your information to: info@ozarkwoodworker.com