The Woodworker’s Prayer

Found this document on The Woodworker’s Prayer in some Shopsmith documents. I liked it, and thought it was funny. So I scanned it in and to share it with all of you.

The Woodworkers Prayer

The Woodworker’s Prayer
Lord, let those
who do not work in wood,
find something else
that’s half as good.

Let me know in the comments if you like this or what you think.

How To: Measure the Size and Swing of a Wood or Metal Lathe

People often ask us how to measure the size and swing of their wood or metal lathe. Lathes are generally described by the maximum size of material that can be cut or machined on the lathe. Before machining a workpiece, the following measurements must be considered: the diameter of the work that will swing over the bed and the length between lathe centers. Often you will see numbers like 14×40 or 9×42 describing the size of a lathe. So what do these numbers mean?

Wood and Metal Lathe Sizes

How to Measure the Lathe Swing and Size

What does the term “swing” on a lathe mean? The first number is referred to as the swing of the lathe which is the maximum diameter of a piece or work that can fit in the lathe. If you have a lathe and want to measure for the swing, you simply measure from the bed of the lathe to the center of the spindle, and then double that measurement. If you measure 6″, then you have a 12″ swing lathe.

Measure Swing of Metal Wood Lathe

 

  • Special Note: Sometimes there can be some discrepancies between the actual measured swing and the swing the manufactures label the machine as being. I’ve only seen this on larger geared head metal lathes and European metal lathes. Some foreign lathes were made on metric standards, and they rounded to the nearest US standard size. Some companies labeled them based on the measurement from the top of the cross-slide for the tool holder on the metal lathe to the spindle.  For example this Bradford Metalmaster geared head metal lathe series had actual measured swings of 14.5″, 16.5″, and 18.5″, but Bradford labeled the lathes as 12″, 14, and 16″.

 

Keep in Mind

On metal lathes, it is important to know the swing over the carriage where your tool holder sits. A lot of companies will give you this specification, and some companies in the past have used this measurement as the size of the “actual” swing of the lathe. It is obvious, if you have to cut something over the carriage of the lathe, it will make your working swing smaller in diameter.

Measure Swing of Metal Lathe

 


 

How to Measure Distance Between Centers on a Lathe

The second number in the sequence 14x40 is referred to as the distance between centers. This is the distance between a center in the headstock to a center in the tailstock. This gives you an idea as to how long the working area of the lathe is. However, a lot of companies in the 40’s or before used the size of the bed as the second number.

Measure Distance Between Centers Metal or Wood Lathe

Depending on what tooling and what kind of cuts, drills, bores, etc… you are trying to use can vary the maximum length of material you can work on in your lathe.

Example:

A 10×24 lathe can handle work that has a diameter up to 10″ and a length between centers of 24.”

Remember:
If you need any help identifying your lathe please feel free to send us pictures and information to info@ozarkwoodworker.com. We’ve identified hundreds successfully.
Please feel free to post comments and questions on this post or any ideas or topics you would like to discuss on future post. And if you need a manual for your lathe, we have all of them listed here at the links below:

Need a manual for your lathe?

Select the Wood or Metal Lathe links below.

 

Wood Metal Lathe Manuals

Machine ID’d: Delta-Rockwell 11″ Wood Lathe model 46-230

Received these pictures of a Delta-Rockwell 11″ wood lathe on a nice heavy duty bench top stand. These were sold under the Homecraft division of Delta. They made a few different versions that look similar. The earlier models had a steel stand. This one has a cast iron stand and is a model 46-230. This lathe has a serial number of 85-7014, which dates it manufacturing to 1950.

We have a couple manuals that cover the 46-230 Rockwell 11″ wood lathe. We have the owner’s manual with operating instructions and parts diagrams here:
We actually combined the older and new versions of this lathe in one book. We also have “Getting the Most Out of Your Lathe” book that Delta published. It covers this lathe and shows a lot of tips and tricks for using and setting up your lathe for different cuts. This is one book of a 6 part series we have in stock. Here is the book on the lathe:
This lathe originally sold for $54.95 in 1950. Below is the page on the lathe from a 1950 Delta-Homecraft catalog. According to the inflation calculator this is equivalent to $532.50 today.
Do you have one of these lathes, or
do you have anything else you would like to add about it’s history or use?
Please add your comments below.

Submit Your Machine
Do you want to know more about your machine?

Email us your details with pictures, and we’ll put together the best information we can find. Plus, we can get other readers’ input to help you learn more.

Also, feel free to email us if you want us to share your machine on our site.

Email your information to: info@ozarkwoodworker.com