Description
Number of Pages: 39
This is a reproduction of an original Foley-Belsaw Model 910, 912 Planer Molder Owner’s Manual, which was rebranded for Craftsman as a model 306.233751. The Model 910, 912 and 9103, 9123 use the same parts diagrams. This manual contains information on setup, lubrication, maintenance, and controls as well as a complete parts list.
Contents:
Specifications………………………………………………………………………………… | 2 |
Safety Rules……………………………………………………………………………………. | 3 |
Illustrated Parts Breakdown……………………………………………………………….. | 4 |
Parts List………………………………………………………………………………………… | 6 |
Illustrated Parts Breakdown & Assembly Instructions for Floor Stand……….. | 7 |
Ordering Repair Parts……………………………………………………………………….. | 8 |
ASSEMBLY AND OPERATING INSTRUCTIONS |
|
Mounting on model 918 Floor Stand……………………………………………………. | 9 |
Motor recommendations……………………………………………………………………. | 9 |
Assembly……………………………………………………………………………………….. | 10 |
Attaching Saw blade…………………………………………………………………………. | 10 |
Slotting Saw Table…………………………………………………………………………… | 12 |
Aligning saw arbor……………………………………………………………………………. | 13 |
Capacity………………………………………………………………………………………… | 14 |
Controls…………………………………………………………………………………………. | 14 |
Lubrications…………………………………………………………………………………….. | 16 |
PLANING AND SAW INSTRUCTIONS |
|
Fundamentals of Planing…………………………………………………………………….. | 17 |
Planing…………………………………………………………………………………………… | 18 |
Sawing…………………………………………………………………………………………… | 19 |
Adjustments……………………………………………………………………………………. | 20 |
Adjustments continued ‘Setting Planer Blades in Cutterhead’………………… | 21 |
Feed speed change…………………………………………………………………………… | 22 |
MOLDING INSTRUCTIONS |
|
Molding knives………………………………………………………………………………… | 23 |
Molding Cutter Bits (One-Inch)………………………………………………………….. | 23 |
Custom Pattern Knives……………………………………………………………………… | 24 |
Using Custom Molding Knives and One-Inch Cutter Bits…………………………. | 28 |
Molding: One-Inch Cutter Bits……………………………………………………………. | 29 |
Guide for molding cuts………………………………………………………………………. | 30 |
Typical set-up for edge molding………………………………………………………….. | 30 |
Molding: Using custom pattern knives…………………………………………………… | 31 |
Edge Knife Catalog Number 384………………………………………………………… | 32 |
Parting Bits Catalog Number 385………………………………………………………… | 33 |
Multiple patterns………………………………………………………………………………. | 33 |
OPERATING CHECK LIST |
|
If board does not feed smoothly………………………………………………………….. | 34 |
If planer vibrates and runs noisy…………………………………………………………… | 34 |
If planed board is not smooth……………………………………………………………… | 34 |
If saw cut is not smooth……………………………………………………………………… | 34 |
What causes a snipe?………………………………………………………………………… | 34 |
SHOP TIPS |
|
Shop Notes…………………………………………………………………………………….. | 35 |
Overview:
I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. I believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. My manuals are not photocopies. I maintain a high standard of quality in my reproductions. Most of the manuals I reproduce look better than their originals. I have professionally digitally edited every page, and removed stains, wrinkles and handwriting. All of the manuals are printed on thick white paper to withstand shop wear and tear.